tqp9107 699 -9 60 m hz 2 - stage power amplifier applications ? wirel ess infrastructure ? repeaters, boosters, das ? high power amplifiers ? small cell bts 3 .5 ? x ? 4 .5 mm l eadless smt p ackage ordering information part no. description tqp9107 699- 960 mhz power amplifier tqp9107 - pcb evaluation board functional block diagram pin 1 reference mark package topside exposed backside pad gnd v bias v cc n/c rfout rfin v pd1 n/c n/c n/c n/c n/c n/c v pd2 12 1 9 6 7 11 4 13 2 10 3 5 8 amp1 amp2 matching network matching network top view product features ? ? ? ? 3 5.5 db gain ? +46 ? dbm output ip3 at pout ? = ? + 24? dbm/tone ? 3 1 % pae at + 27? dbm pout ? internally matched ? integrated inter - s tage m atching ? bias adjustable ? low idle current general d escription the tqp 9107 is a high - efficiency two - stage power amplifier in a low - cost surface - mount package. the amplifier is able to achieve 3 1 % power added efficiency at +27?dbm output power order imd products are below ?17?dbm at all output power levels below +24 dbm/tone. the tqp9107 integrates two high performance amplifier stages onto a module to allow for a compact system design and requires very few external components for operation. the amplifier is bias adjustable allowing the amplifier?s power consumption to be optimized . the tqp 9107 is available in a lead - free/rohs - compliant 13 - pin 3 .5? x ? 4 .5 mm surface mount package and is pin - compatible to the hig her frequency band version in the family with the tqp9108 (1.7 - 2. 17 ghz). pin configuration pin no. label 1 v bias 2 v cc 3, 4, 5, 6 , 8, 9, 10 gnd or n/c 7 rf out 11 v pd1 12 v pd2 13 rf in backside pad gnd advanced data sheet: rev e 1 0 - 2 9 - 14 - 1 of 9 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
tqp9107 699 -9 60 m hz 2 - stage power amplifier recommended operating conditions pa rameter min typ max units v cc , v bias + 4.3 +5 v v pd1, v pd2 +4.0 +5 v t case - 40 + 85 c tj for >10 6 hours mttf + 190 c electrical specifications are measured at specified test conditions. specifications are not guaranteed over all recommended opera ting conditions. absolute maximum ratings parameter rating storage temperature ? ? ?v rf input power, cw, 50, t=25 ? electrical specifications test conditions unless otherwise noted: v cc = v bias = +4.3?v, v pd 1 = v pd2 =+4.0 v , temp= +25 ? c, 50 system . parameter conditions min typ max units operational frequency range 699 96 0 mhz test frequency 849 mhz gain 28.8 3 5.5 db noise figure 5 db output p1db 31.4 dbm output ip3 pout ? ? ? dbm/tone, f ? ? ? ? ? 2 3 ? db m ? / ? tone ? 17 dbm current, i cc pout ? = ? +27 ? dbm 3 7 0 ma power added efficienc y pout?=?+27?dbm 31 % idle current no rf input power 84 ma thermal resistance, - 2 of 9 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
tqp9107 699 -9 60 m hz 2 - stage power amplifier application circuit schematic diagram 12 1 9 6 7 11 4 13 2 10 3 5 8 amp1 amp2 matching network matching network j2 rf output j1 rf input c6 10 uf v pd c7 0.47 uf r1 0 ? v cc r2 0 ? c5 100 pf j1 j2 j3 j6 j4 j5 r4 r3 c5 r2 r1 c7 c6 u1 bill of material reference des. value description manuf. part number nelco fr4, p cb app board triquint 1109803pc u1 2 - stage power amplifier triquint tqp910 7 c5 100 pf cap, 0603, 5%, 50v, npo various c6 10 uf cap, 6032, 20%, 50v, tantalum various c7 0.47 uf cap, 0603, 50v, x7r, 5% r1, r2, r3, r4 0 ? res, 0603, 5%, 1/16w, chip various advanced data sheet: rev e 1 0 - 2 9 - 14 - 3 of 9 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
tqp9107 699 -9 60 m hz 2 - stage power amplifier typical performance test conditions: v cc =+ 4.3 v, temp.=+25c, 50 system parameter conditions typical value units frequency 760 820 850 920 mhz gain 35.0 35.8 35.7 34.1 db im3 pout= + 27 dbm, ? f= 600 k hz - 30 - 27 - 24 - 17 dbm im5 pout= + 27 dbm, ? f= 600 k hz - 22 - 21 - 20 - 21 dbm quiescent collector current, i cq v pd = 4v 84 ma performance plots 32 33 34 35 36 37 700 750 800 850 900 950 gain (db) frequency (mhz) gain vs. frequency temp.=+25 c 0 10 20 30 40 50 60 26 27 28 29 30 31 32 33 pae (%) pout (dbm) pae vs. pout temp.=+25 c freq = 850 mhz -50 -47 -44 -41 -38 -35 -32 -29 -26 -23 -20 -17 -14 -11 20 21 22 23 24 25 26 27 28 im3 (dbm) pout (dbm) im3 vs total pout (699 mhz) im3 lower im3 upper tone spacing = 600 khz temp.=+25 c -50 -47 -44 -41 -38 -35 -32 -29 -26 -23 -20 -17 -14 -11 20 21 22 23 24 25 26 27 28 im3 and im5 (dbm) pout (dbm) im3 and im5 vs total pout (760 mhz) im3 lower im3 upper im5 lower im5 upper tone spacing = 600 khz temp.=+25 c -50 -47 -44 -41 -38 -35 -32 -29 -26 -23 -20 -17 -14 -11 20 21 22 23 24 25 26 27 28 im3 and im5 (dbm) pout (dbm) im3 and im5 vs total pout (820 mhz) im3 lower im3 upper im5 lower tone spacing = 600 khz temp.=+25 c -50 -47 -44 -41 -38 -35 -32 -29 -26 -23 -20 -17 -14 -11 20 21 22 23 24 25 26 27 28 im3 and im5 (dbm) pout (dbm) im3 and im5 vs total pout (850 mhz) im3 lower im3 upper im5 lower tone spacing = 600 khz temp.=+25 c -50 -47 -44 -41 -38 -35 -32 -29 -26 -23 -20 -17 -14 -11 20 21 22 23 24 25 26 27 28 im3 and im5 (dbm) pout (dbm) im3 and im5 vs total pout (920 mhz) im3 lower im3 upper im5 lower tone spacing = 600 khz temp.=+25 c -44 -41 -38 -35 -32 -29 -26 -23 -20 -17 -14 -11 20 21 22 23 24 25 26 27 28 im3 (dbm) pout (dbm) im3 vs total pout over temperature (850 mhz) 25degc 45degc 55degc 65degc tone spacing = 600 khz -44 -41 -38 -35 -32 -29 -26 -23 -20 -17 -14 -11 20 21 22 23 24 25 26 27 28 im5 (dbm) pout (dbm) im5 vs total pout over temperature (850 mhz) 25degc 45degc 55degc 65degc tone spacing = 600 khz 30 35 40 45 50 55 20 21 22 23 24 25 26 27 28 oip3 (dbm) pout (dbm) oip3 vs total pout 699 mhz 760 mhz 820 mhz 850 mhz 920 mhz tone spacing = 600 khz temp.=+25 c advanced data sheet: rev e 1 0 - 2 9 - 14 - 4 of 9 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
tqp9107 699 -9 60 m hz 2 - stage power amplifier typical performance at vcc = 5v test conditions: v cc =+5 v, vpd=+4.3 v, temp.=+25c, 50 system parameter conditions typic al value units frequency 750 840 880 940 mhz gain 35.5 36.2 35.8 34.0 db input return loss - 13 - 9 - 9 - 10 db output p1db 32.9 32.5 32.1 31.9 dbm output ip3 pout= +24 dbm/tone, ? f= 1 mhz 42.1 43.5 44.0 46.2 dbm quiescent collector current, i cq 87 ma performance plots 28 30 32 34 36 38 700 800 900 1000 gain (db) frequency (mhz) gain vs. frequency temp.=+25 c 30 31 32 33 34 35 750 800 850 900 950 p1db (dbm) frequency (mhz) p1db vs. frequency temp.=+25 c 30 35 40 45 50 14 16 18 20 22 24 oip3 (dbm) pout/tone (dbm) oip3 vs. pout/tone 750 mhz 840 mhz 880 mhz 940 mhz 5 0 00 00 00 400 500 00 700 800 900 000 5 0 5 0 5 0 5 5 -60 -55 -50 -45 -40 -35 -30 14 15 16 17 18 19 20 21 22 23 24 25 aclr (dbc) pout (dbm) aclr 750 mhz 840 mhz 880 mhz 940 mhz w - cdma 3gpp test model 1+64 dpch par = 10.2 db @ 0.01% probability 3.84 mhz bw advanced data sheet: rev e 1 0 - 2 9 - 14 - 5 of 9 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
tqp9107 699 -9 60 m hz 2 - stage power amplifier pin configuration and description pin 1 reference mark package topside exposed backside pad gnd v bias v cc n/c rfout rfin v pd1 n/c n/c n/c n/c n/c n/c v pd2 12 1 9 6 7 11 4 13 2 10 3 5 8 amp1 amp2 matching network matching network top view pin no. label description 1 v bias provides reference voltage for internal active biasing circuit 2 v cc dc voltage supply connection 3, 4, 5 , 6, 8, 9, 10 n/c no internal connection. provide grounded land pads for pcb mounting integrity. 7 rf out rf o utput pin. the dc is internally blocked at this pin. 11 v pd1 power down for amp 1. this voltage adjusts for the current draw in amp 1. 12 v pd2 power down for amp 2. this voltage adjusts for the current draw in amp 2. 13 rf in rf i nput pin. the dc is internally blocked at this pin. backside pad gnd rf/dc ground. use recommended via pattern to minimize inductance and thermal resistance; see p cb mounting pattern for suggested footprint. advanced data sheet: rev e 1 0 - 2 9 - 14 - 6 of 9 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
tqp9107 699 -9 60 m hz 2 - stage power amplifier package marking and dimensions marking: part number ? 9107 date - yyww lot code ? aa xxxx top view 0.920.08 0.10 c 4.50 4.500.1 2.25 3.500.1 1.75 2x 0.10 c 2x 0.10 c b a pin #1 locator side view bottom view 3.5000.1 1.080 1.000 2.000 1.000 2.000 0.680 1.080 0.750 1.500 2.000 1.080 0.500 1.000 1.500 2.000 4.5000.10 1.480 1.480 (1x) shape 0.10 c a b pin1 (10x) 0.270x x 0.340y 0.10 c a b (1x) 0.770x x 0.340y 0.10 c a b (1x) 1.270x x 0.340y 0.10 c a b c notes: 1. all dimensions are in millimeters. angles are in degrees. 2. except where noted, this p art outline conforms to jedec standard mo -229. 3. dimension and tolerance formats conform to asme y14.4m - 1994. 4. the terminal #1 identifier and terminal numbering conform to jesd 95 - 1 spp - 012. 9107 yyww aaxxxx advanced data sheet: rev e 1 0 - 2 9 - 14 - 7 of 9 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
tqp9107 699 -9 60 m hz 2 - stage power amplifier pcb mounting pattern recommend pcb land - pad pattern metallizat ion (top view) recommended pcb solder mask opening (top view) notes: 1. a heat sink underneath the area of the pcb for the mounted device is strictly required for proper thermal operation. damage to the device can occur without the use of one. 2. groun d / thermal vias are critical for the proper performance of this device. vias should use a .35mm (#80 / .0135?) diameter drill and have a final plated thru diameter of .25 mm (.010?). 3. add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. advanced data sheet: rev e 1 0 - 2 9 - 14 - 8 of 9 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
tqp9107 699 -9 60 m hz 2 - stage power amplifier product compliance information esd sensitivity ratings caution! esd - sensitive device esd rating: class 1c value: passes 1000v to < 2000 v test: human body model (hbm) standard: jedec standard js - 00 1 - 2012 esd rating: class c3 value: passes 1000 v test: charged device model (cdm) standard: jedec standard jesd22 - c101 solderability compatible with both lead - free (260 c max. reflow temperature) and tin/lead (245 c max. reflow temperature) sol dering processes. package lead plating: electrolytic plated au over ni rohs compliance this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipment). this produc t also has the following attributes: ? lead- free ? halogen free (chlorine, bromine) ? antimony free ? tbbp - a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free msl rating msl rating : level 3 test: 260c convection reflow standard: jedec standard ipc/jedec j - std - 020 contact information for the latest specifications, additional product information, worldwide sales and distribution locations, and information about triquint: web: www.triquint.com tel: +1.503.615.9000 ema il: info - sales@triquint.com fax: +1.503.615.8902 for technical questions and application information: email: sjcapplications.engineering @triquint.com important notice the information contained herein is believed to be reliable. triquint makes no warranties regarding the information contained herein. triquint assumes no responsibility or liability whatsoever for any of the informat ion contained herein. triquint assumes no responsibility or liability whatsoever for the use of the information contained herein. the information contained herein is provided "as is, where is" and with all faults, and the entire risk associated with such information is entirely with the user. all information contained herein is subject to change without notice. customers should obtain and verify the latest relevant information before placing orders for triquint products. the information contained herei n or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. triq uint products are not warranted or authorized for use as critical components in medical, life - saving, or life - sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. advanced data sheet: rev e 1 0 - 2 9 - 14 - 9 of 9 - disclaimer: subject to change without notice ? 201 4 triquint www.triquint.com
|
